1545 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Braille Clock/Watch
Instructions from Braille Clock/Watch
If everything works perfectly, you can close the box. If not, verify if all instructions have been correctly done.

Put Everything Together And Finish Up
Instructions from 3D Printer Light Bar
Put the light bar, angle makers, adaptors, and the switch box together and connect them to the V-slots.It's done!

Combining them all together
Instructions from Noisy Meter
This was the easiest part according to me. Added in the arduino board first then the mini breadboard that the sound sensor and the OLED display were attached to. I used glue gun to secure everything in place. Then I gave the box a makeover. In the future,...

Trombino
Instructions from Trombino
Place the lid close to the bottom and wire everything in, trying to keep the wires short. There is very little clearance at the top of the case so anything attaching to the shield should not have extra height (eg no jumper cables!). After everything...

1Charger
Instructions from 1Charger
Time to think inside the box...1. Flash ATtiny without CALIBRATION defined ( see step 4 )2. Verify everything works as expected3. Assemble project box and solder connectors.\(^_^)/ DONE !

Oro the SMS alarm temperature watchdog
Instructions from Oro the SMS alarm temperature watchdog
I bought the enclosure at my local electrics store and hot glued everything in place.The cutout for the temperature/humidity sensor was made with a box cutter.The Arduino source code can be downloaded here: Project Oro

Wood Working
Instructions from DIY emergency power system - a field report
After the wiring was done, I lined the inside of the box with wood and connected everything with wood glue. The panel above the battery is only laid on and can be opened for maintenance purposes.

Put everything together
Instructions from The Interactive Book
6. The last and most challenging step was to put all our work together. We had to place all the sensors inside the box, make sure they fitted perfectly. We had to link the voice telling the story with the code and sensors, and also link them with the...

take it apart and inspect it
Instructions from Dial-a-Memory
This is the interesting part. Two phones which have the same function, and look almost exactly the same on the outside can be engineered completely differently inside. Some have discrete components visible, some have everything hidden in...

Miter-box cuts (mostly 90 degrees but precise)
Instructions from The Learner's Heliostat
Frame the UJ as shown except that the chamfer is on the wrong end. Complete the cuts and keep an eye on the humidity. I gather that for best results, you condition all lumber in the room where it will be cut (done) and cut everything the same day. (Or...

Trombino
Instructions from Trombino
Drill two holes in the lower half of theArduino box and fix it to the top of the potentiometer housing. Thread wires through the holes. Add in the Arduino, ethernet shield and breadboard and hook up the parts currently attached to the housing. Open up...

Adjust the trimpots for gas measurements
Instructions from Solar Powered Air Quality Monitoring Station (IoT)
Move everything inside the box and adjust the trimpots to calibrate the measurements.Precise calibration wihout a known concentration of each gas is not possible, however the datasheet of the sensor recommends to calibrate the output to 2.5V and you...

1Charger
Instructions from 1Charger
There can be only oneComplete the 1Charger by soldering the two circuits together ( from step 7,8 )Solder current sense to ATtiny861* new -Vout to PA5 ( pin13)* old -Vout to PA6 ( pin12)Solder 3.3V buck-boost supply to new Vout* Vcc+ to new +Vout...

Electronic
Instructions from GRawler - Glass Roof cleaning crawler
The electronic part can be soldered to a breadboard. See the attached schematic for detail. I also attaches the eagle sch-file if you like to make your own pcb. To protect the electronic from moisture, everything including the batteries can be built...

Software
Instructions from ESP 8266 Square Inch Wifi Datalogger
Upload test program and look at serial where you should see values from sensors. If everything works create google spreedsheet and copy gs script to script. You have to edit script and add there your spreedsheet id. After that create Pushing box account...

1
2
3
4
5
>
>|