1088 Results for "S%20%ED%86%A0%ED%86%A0%EC%B6%94%EC%B2%9C%EC%97%85%EC%B2%B4%20CDDC7.COM%20%E2%99%AA%EB%B3%B4%EB%84%88%EC%8A%A4%EC%BD%94%EB%93%9C%20B77%E2%99%AA%ED%86%A0%ED%86%A0%ED%94%BC%EC%A7%80%EC%BB%AC%E0%BE%AA%ED%94%BC%EB%A7%9D%ED%8F%AC%EC%BB%A4%EC%BF%A0%ED%8F%B0%E2%98%B8%EC%B9%B4%EC%A7%80%EB%85%B8%EC%A7%81%EC%97%85%E2%8B%94%EC%8B%A4%EC%8B%9C%EA%B0%84tv%EC%A4%91%EA%B3%84%DA%A2%ED%86%A0%ED%86%A0%EC%B6%94%EC%B2%9C%EC%97%85%EC%B2%B4%EC%82%AC%EB%9E%91%20dissimilarity/"

Components of the AC Indoor Unit
Instructions from Air Conditioner PCB Tutorial With its Working
Some of the main components inside an AC Indoor Unit apart from the PCB are:- 1) Blower Unit:- It is a blower fan that rotates in such a way that from one end it takes the hot air inside and from the other end it sends out the cooled air. In this unit...

Print the 3D Enclosure - specifically, the AC plug SHIM is needed prior to PCB assembly
Instructions from AC Wall Adapter PCB for IoT
The Plug Shim (spacer) is needed to assemble the PCB. It must be installed before soldering the AC plug to the PCB and the AC plug itself must be soldered to the PCB before the AC-DC Converter Module

Understanding how to disconnect the speaker
Instructions from Hush Owlet
moThe big black device in the middle of the printed circuit board (PCB) is the speaker (aka buzzer, or transducer). You can see a little slit in the one side where the sound comes out. There is a back side to the circuit board that you cannot easily...

Fathom-S topside assembly
Instructions from OSUG: Open-Source Underwater Glider
Cut a ~10cm length of the tether cable and strip it down to the pairings. Strip the ends and tin one end of each wire as shown below. Solder the other end into a breadboard and also solder an 8 pin male KK series connector. Make sure that the wires and...

Full build instructions can be found below
Instructions from Thermochromic Display - PCB Version
https://www.instructables.com/id/Thermochromic-Temperature-Humidity-Display-PCB-Ver/

The PCB´s Are Here
Instructions from 5-12V Capacitive Touch Switch
8 days after ordering, the prototype PCBs finally arrived. They look simply great.

First, let's talk about the board and everything that will be necessary for it.
Instructions from Control your audio with theKnob
The PCB itself is an extension PCB for a microcontroller board "DFrobot beetle". It allows us to keep everything in place and make it compact and also, it's easy to solder everything. Please follow the steps strictly, because the design of the...

How the PCB was designed and how it can be build
Instructions from Venta Connected
See my blog: http://wiki.kainhofer.com/hardware/venta_connected

Solder in the breadboard power rail header(s) (optional)
Instructions from RC Servo Adapter
Install the board with the signal header down into the breadboard and look through the holes over the power rail to see which ones line up. Pull it up, insert 2x1 pin headers in those locations (or location) and then put the PCB back down and solder...

Heat sink Prep (6"x6"x6mm base suggested) fins should be about 1.5" or 20mm deep.
Instructions from 45W RF SSB CW AMP (EBAY) DIY Build = 55W Upgrade
Drill (2.5mm or 3/64") and tap (4-40 or 3mm) the screw holes. Obtain 1/2" pan head screws to match. Place the PCB with the transistors on the heat sink and align the TO-220 TAB holes to the tapped heat-sink holes. Melt the solder joint on the transistor...

For full instructions, please visit: https://s-u-pm-sensor.gitbook.io/pyonair/
Instructions from PyonAir - IoT air pollution monitor
To avoid confusion, the following instructions will only cover the steps for making a PyonAir monitor using the PCBA approach. If you'd like to hand-solder the PCB or use breadboard, please visit: https://s-u-pm-sensor.gitbook.io/pyonair/tutorial/wiring/...

Fan controller for Re:Load Pro
Instructions from Fan controller for Re:Load Pro
Make you the PCB and get the components and any standard 60mm 4-wire fan will probably do the job. I used a JMC "6015-12HB APW" that I had lying around. The exact the same fan is readily available on eBay.I used eagle to design my PCB, and the files...

Program the Microcontroller
Instructions from Fear the Scary Cat!
Before mounting the prototype PCB to the housing, I recommend uploading the required sketch to the ATtiny84 microcontroller with a programmer of your choice. I used a USBtinyISP type shown in the picture. /*Sketch for the Scary Cat Project by Gene H*/...

Instructions
Instructions from Budget DIY ESP32 GPS Base Station and Receiver
Best Budget DIY GPS/GNSS Base Station using the UM980 and a ESP32Introduction The ESP32 is a versatile microcontroller renowned for its WiFi and Bluetooth capabilities. In this guide, we’ll walk you through setting up the your ESP32 development board...

1
2
3
4
5
>
>|