6194 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Bootstrapping
Instructions from External Captions for Video Installations (extsub)
If everything is working, press ctrl+c to kill extsub.py, then follow these steps to run extsub at boot. 1. Make startup.sh executable: chmod 755 startup.sh 2. Open /etc/rc.local: sudo nano /etc/rc.local and add this line so extsub...

From CAD to 3D
Instructions from Replacement Faceplate for Pyle PLMR24 Speakers
Once the CAD model was created, it was a simple matter of loading the STLs into the Cura slicer and sending the data to the 3d printer. I printed everything at a 0.3mm layer height, since it didn't have to be perfect. Even at that, it looks pretty good....

Bolt on Modules
Instructions from Autonomous Agri-robot Control System
The Ublox bolts onto the underside of the PCB and all the others on the top. Push them all into place and check that they work OK. The TC275 TFT screen will not work unless the EMIC2 serial1 in AND out are connected. Serial 1 is normally right next...

Plugging Everything In
Instructions from Pentesting BBU Dropbox
This is the wiring part. Just follow the schematic. Plug in the Pi's USB cable for power. Plug the short patch cable into the Pi & the other end into the switch. Plug the patch cables coming from the RJ45 jacks into the switch. Plug the red wire from...

Repeat
Instructions from Quiz-o-matic wireless buzzers
Printed and soldered everything again 3 more times. I ran out of 2 AA battery holders so I hacksawed a 4 AA holder in half and soldered wires to appropriate terminals. I also took care to flash each board with a different DEVICE_ID (see the .ino file)...

Solder the SAO Fix to the Add-on
Instructions from SAO Rejects
Once you've assembled both the Add-on and the SAO Fix board now you can attach them. Simply place the Badge through the side of the board labeled "Add-on" so that at the bottom "Badge" is visible and solder the headers into place.Once...

Step 1 : Gather everything let's get our hands dirty...!!!
Instructions from Convert your old phone into a remote switch
Gather all required parts. Now you need to disassemble your old phone so that you will have access to the vibration motor connections. I have attached a video of disassembly of Nokia 3310. But the procedure will be same for almost all basic phones.Open...

Designing and constructing the Paludarium
Instructions from Edens.Bow
It all started with a 55 gallon bow front aquarium. It was a used system that came with everything needed to function correctly. The filtration system was a simple over flow set up that channeled water into an under tank sump, where the water was filtered...

Connect RFID Reader and Test
Instructions from The ULTIMATE Raspberry Pi Smart Home Door Lock
Now it’s time to connect everything up, including the RFID reader, and see if it works! Take your RFID fob and hold it to the reader. It recognises that as me, and displays my name and photograph. I then enter my PIN, 1 2 3 4 5 6 and it then generates...

Step 6: Test!
Instructions from Android IOT – Remotely Controlling ESP32
Run the app by pressing the play button and test by pressing the buttons. If everything has been done correctly you will be able to turn the relay on and off using the buttons and detect the state of the relay by pressing the state button. If the communication...

Testing Functionality
Instructions from Fight Coronavirus: Simple Handwash Timer
Once you have successfully uploaded the code, it's time to check if the timer works correctly before putting it into an enclosure. Normally all the LED should be off. Take your hand in front of the sensor, the red LED should turn on. Eventually all the...

3D Printing
Instructions from Positivitypunk Backpack
To print bolt holes, offset from the plane of the printer, I created 4 cylinders and aligned them a layer or two below where the hole would start to print. Each cylinder is a solid model, two layers thick. Once sliced, support will not need to be generated,...

Solder everything together
Instructions from Reimagining Duo Pop
1. Use the reference picture and wiring diagrams below to solder all the pieces. Your finish product may not look like mine and that is okay. Wire it in the most convenient method. I measured each wire cut and stripped the ends and then soldered them...

Setup Debugger
Instructions from SWO with Mbed Studio
From Mbed Studio, select Target and click the little chip to set up a new debug probe. Under Debug Flags, you'll find a large number of items populated once you pick the USB device. Add the following (don't change anything that is there): -O enable_swv=1...

Prepare the Parts
Instructions from Internal Battery Mod for Korg NTS-1 Synth
The first step is to disassemble your Korg NTS-1 and remove the main board. You don't need to unscrew everything for that, you only need to remove the back panel and loose the screws of the side panels where the connections are to be able to remove the...

|<
<
2
3
4
5
6
>
>|