Close

65 Results for "%E3%80%8A%20%EC%98%88%EC%95%BD%EB%AC%B8%EC%9D%98%20OIO%E2%89%A1%E2%91%A7%E2%91%A389%E2%89%A183O%E2%91%A5%E3%80%8B%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%EA%B2%AC%EC%A0%81%E3%82%88%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8ago%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%83%A1%EA%B0%95%EB%82%A8%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8eighty%20%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%CE%BA%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%E2%92%B2%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8%E3%83%A1%EF%BD%83%EC%84%A0%EB%A6%89%EB%A0%88%EA%B9%85%EC%8A%A4%EB%A3%B8literary"

  • Cuts required

  • The plywood product I used was 1/2x2x4 G1S, $37 ea before tax in Ontario in summer of 2022. For the project infrastructure, four 1" x 4" x 8' knotty pine planks would be price competitive and less work to waterproof, but less convenient to transport....
  • Instructions for small generator

  • howto make a generator1. 3V Dc motor – inside toys which using two batteries 1.5 V AA 2. coil without core inside syncronous motor 230 V – A4 laminators, microwave turntable motor - remove the core inside the motor 3. neodymium magnet sphere 13 mm 4....
  • Construction of Probe

  • Cut 2.0 x 1.5 breadboard lengthwise such that one piece had the center screw holes intact.   P1 is pressure side of pressure sensors.  P1 is port closest to Pin 4.  Pin 1 is the notched pin.  Solder pressure sensors to breadboard...
  • Cutting the Acrylic

  • For this step you will need: Acrylic sheetsSawPencil I am using some 3mm thick opal acrylic to diffuse the light for this project. I purchased some A4 sheets which we can cut three panels worth of acrylic diffusers from. My fourteen triangles therefore...
  • Arduino GPRS IOT Weather Station

  • Arduino Soil Probe Using DS18B20 and DIY Moisture Hardware:As a fanatical gardener or a professional farmer, knowing the environmental conditions of our soil is invaluable. Obviously, we can't measure the number of worms or pieces of organic humus, but...
  • The Dune Pain Box

  • Winding the inductors is easier than you might think!  I used about 4 feet of 18GA Magnet wire to wind the inductors for this particular power supply.  Each inductor has ~30 turns on it for an inductance of about 90uH.  If you don't have...
  • Back Panel

  • The components are attached to a baseplate (95(W) x 128(L) mm), which is fitted to the back of the MDE's with M3 X 25mm bolts and 10mm standoffs. Four bolts are fitted through the holes in the Neopixel support board and the standoffs fitted to attach...
  • CODE

  • The first code chunk declares the variables and establishes connections #include #include "Wire.h"#include #include "GravityTDS.h"#include #include #include "MS5837.h"#include "ping1d.h"#include "SoftwareSerial.h"#include "RTClib.h"#include //#include...
  • Clunke Button

  • Making one button takes me about 8 hours of printing and 1 hour of assembly.MaterialsCherry MX Switch3.5mm Mono Port6" or so of wireOptional: Compression spring for adjusting the button's actuation force.Optional: 3.5mm Mono cable to connect the button...
  • Assemble your Extruder

  • First, let's assemble the extruder, so we can just drop it onto the printer later! There are two sets of spacers, labeled B1-B7 for the Bottom assembly, and T1-T2 for the top assembly. There is also an extruder motor shaft coupler spacer, labeled...
  • Use CoilCalc to characterize an existing coil

  • # # Example coil: Diameter 50mm, Length 200mm, with 35 turns # > CoilCalc --D=50 --l=200 --N=35 --d=1.44 --f=13.562 # QOIL™ — https://hamwaves.com/qoil/ — v20181217 # Coil design 2023-03-11 12:20 # INPUT # mean diameter of the coil D = 50.0 mm # number...
  • Connect your Wires

  • 1. Make the cable guide. Cut a 6-flute section out the 36" 10mm Corex sheet, and then make scores (not cuts) at 1" intervals, starting at one side, and moving inward 18". Use a razor blade and straight edge to make scores perpendicular to the flutes...