2002 Results for "《〈 문의 OIO↗5793↗7458 》〉 셔츠룸ヒ《〈 문의 OIO↗5793↗7458 》〉㎛beforehandム셔츠룸후기셔츠룸후기╇pen 선릉셔츠룸셔츠룸가격 셔츠룸‰강남셔츠룸㉦nestㅳ"

The world's first paper quadcopter
Instructions from The world's first paper quadcopter
Get a piece of 3.5 x 8.5 form board or or you can use cardboard if you use cardboard you will need 2 3.5 x 8.5 just glue them together to make one solid piece.Lay the short tubes on the sides of the board and the long tubes across the top to form the...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Lexitron circuit design and hardware:LED display: The display is constructed using Red 8x8 square LED matrix displays, each containing 64 LEDs wired in a square grid with the 16 column and row pins available out the base. It is designed to be used in...

Lexitron RSS Reader
Instructions from Lexitron RSS Reader
Tickernut construction log:Construction was completed in stages over the period of many months with a design that evolved to suit the available parts. The progression of construction was arranged so that each stage could be completed and tested...

ROSCOE - A Scalable, Platform Independent Robot
Instructions from ROSCOE - A Scalable, Platform Independent Robot
Mechanical:There are special application 16 inch 32 hole rims available at e-bike shops/online. Provide the hub and have the spokes cut to length. To build the wheel it is necessary to add the spokes all to one side, dished all the way in, add...

ROSCOE - A Scalable, Platform Independent Robot
Instructions from ROSCOE - A Scalable, Platform Independent Robot
Mechanical:For stabilization of wheels a carriage is constructed consisting of 5/8" stainless all-thread and a 16 inch BMX bike fork. 1) Drill 2 3/8" holes 1" from each end of the steerer tube.2) Bisect the fork longitudinally along the steerer...

Infinity Mirror Clock
Instructions from Infinity Mirror Clock
The clock is primarily made up of the following: 2 pieces of 8mm plywood (600mm x 600mm) - needs to be cut as per the schematic above1 piece of 18mm block-board (600mm x 600mm) - needs to be cut as per the schematic above. Please be careful with the...

1Charger
Instructions from 1Charger
Calibration1. #define CALIBRATION in software and recompile and flash ATtiny8612. For each range make two measurements in order to calculate the line v=k*ADC + m. With this simple approach I get about 10-20mV and 10-20mA accuracy ( compared...

1Charger
Instructions from 1Charger
Calibrate connected-ish ( serial port )The serial port is useful for making charge curves and debug. I use a usb to serial cable that accept 3.3v level.Connect the serial cable to GND and pin PA7The software UART timer interrupt is also used as a timebase....

ATX-Pi
Instructions from ATX-Pi
Step two: Place the R6 (1k ohm), R7 (10k ohm), the 16 MHz crystal (XTAL) and the 22 pF capacitors (C1/C2). Solder in place.

Window Fan Controller
Instructions from Window Fan Controller
// Temperature Controler for window fan// Written by mike, public domain/*-------------------------------------------------------------------------------------- Includes--------------------------------------------------------------------------------------*/#include...

nRFIoT - Easy IoT Sensors
Instructions from nRFIoT - Easy IoT Sensors
You can put the board and pro mini together with these. Or you can do it your own way. You will have to trim one side of the headers if you do what I did to give the radio module room. (You'll see what I mean). At a minimum, you must connect the...

3D(ollar) Scanner
Instructions from 3D(ollar) Scanner
8. Take picture using program local to OS: -use GIMP or other program to find pixels and locate coordinates for center of platter-set resolution in the video_line_viewer to the size your camera outputs.. manually :(-determine angle, in radians of platter...

8-bit Jukebox
Instructions from 8-bit Jukebox
Assemble the case: Add a little glue to the edges of each plate (A-1 through A-5) and press fit them together. The arrows and letters on plates A-1 through A-4 should match up as shown in Image 1. You might want to use some...

Modular Clock Kit
Instructions from Modular Clock Kit
The Clock Logic board is 3.75" x 2.50".The I.C.s are spaced two (2) rows apart.I started on one end with the simple power supply, wave shaper and divide by 60 circuits.Next is the inter-stage logic. The heart of the clock.The various resets, divide by...

DMX-84: Calculator-Controlled Lights
Instructions from DMX-84: Calculator-Controlled Lights
Ensure the Arduino IDE is setup to build for "Arduino Pro or Pro Mini (5V, 16 MHz) w/ ATmega328" and that the selected serial port corresponds to the FTDI.

|<
<
4
5
6
7
8
>
>|