1804 Results for "Q%20%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%20CDDC7_C%D0%9EM%20%E2%97%86%EB%B3%B4%EB%84%88%EC%8A%A4%EB%B2%88%ED%98%B8%20B77%E2%97%86%EC%88%98%EC%9B%90%EC%9E%A5%EC%95%88%20%ED%94%84%EB%A1%9C%ED%86%A0%20%EA%B5%AC%EB%A7%A4%E0%B9%8F%ED%86%A0%ED%86%A0%ED%95%AB%ED%94%BD%E2%8F%AC%EC%98%A8%EB%9D%BC%EC%9D%B8%ED%99%A9%EA%B8%88%EC%84%B1%E0%BC%88FX%EB%A7%A4%EB%A7%A4%E2%8B%8D%EC%95%88%EC%82%B0%EB%B8%94%EB%9E%99%EC%9E%AD%EC%95%A0%EC%9A%A9%20thorough/"
Prerequisites This tutorial expects you to already have an account with balenaCloud and a Raspberry Pi provisioned. If you haven't, we have an excellent set of getting started guides to get you up and running. Software Before touching the hardware,...
PCB Rev 1.0 Errata:Diode D3 is reversed in the board silkscreen. Place it backwards (opposite of what is shown) for a positive supply, and normal (as shown on the silk screen) for a negative supply. Rev 1.1 has been changed to be correct.Crystal X1 is...
Open connection nipple 3-D drawing with Sketchup 2014. Select the first part. Then click on the drop down menu for 'File' and select 'Export STL...'. When the 'STL Export Options' window opens, select 'Export selected geometry only', 'Export unit: Millimeter'...
Install Motor Mounts and Align MirrorsNext we install the motor mounts into the case. I just used 2 sided tape so I can re-align it or repair it if necessary. (You can glue your in if you want though.) Once the motor assembly is installed in the case,...
Step 7: Electronic ComponentsWe are now done with the mechanical set up of our longboard. Next, we need to wire up the VESC to the batteries and receiver. It is a very straight forward procedure. Before we start, make sure all connectors are compatible....
Make the Air Tank-You can make an air tank a couple of ways. #1 is you can just buy one, for like $30 on ebay (rover.ebay.com/rover/1/711-117182-37290-0/2open_in_new), or use a bulkier tank, one of those white ones. This is how to make a air tank outta...
There are 5 things that need to be soldered onto the motor shield. I've found this order of soldering to be easiest: Start by soldering a 6 pin 90 degree header on the back as shown in photos. They are unlabeled but it’s the 3rd to 8th pins from...
Rover is characterized by four corner assemblies attached to a central frame. Build the corner assembly as follows:Print the sun, ring, and planet gears first. Then the planet carrier aka output, the gearbox cap, the wheel rim and wheel cap. The...
Cut one sheet of 8x4 feet plywood as shown below: Cut the unused 12"x30" piece into 24 3"x5" blocks.Lay the pieces out as seen in the second part of the image.(Pre-drill all screw holes in the following steps.)Attach B,C,J to A with long screws...
If you have been working with HDMI and the Raspberry Pi not connected to the RCA/FBAS display, you should now put the Raspberry Pi inside the Retro LED-Beamer and connect the RCA/FBAS output to the display. Start everything up, you should see a small...
The installation of the steering actuator is shown below, it's a thumping great 4000 N device capable of tearing the whole machine apart if not careful. The actuator needs to be able to turn slightly at each end and so is mounted on the stainless steel...
Hypothesis: Laser pulse frequency is too slow Discussion: The laser settings has a pulse frequency setting. Is the ragged edge due to laser pulses as the beam travels across the work? Experiment: Change the laser pulse settings and see if the problem...
In a maze, for locomotion from one point to another, there are more than one way to reach the spot. But the question is, which is the shortest path to reach the spot? A maze consists of 90º sharp turns. So, we shall consider that, and find a logic...