1154 Results for "solder fume extractor"

7. Unsoldering Components With Infineon Version
Log from Work-holding Robotic Arm for Electronic Workshop
Now, I show you how to use the CAPSENSE technology to unsolder components, and again using the PSoC 62S2 WiFi BT Pioneer Kit board. Below I show you the schematic diagram. Schematic Diagram Schematic diagram How does it work? Here I will use the device...

$150 Pick and Place Machine*
Details from $150 Pick and Place Machine*
(Skip to 2:50 to see it in action!) A Highly Specialized Pick & Place Machine First, some prerequisites: Your board must fit within the print area, with about 3" to spare in each directionYour board must only have 1-2 BoM itemsSingle-sided assembly onlyThese...

Solder everything together
Instructions from Reimagining Duo Pop
1. Use the reference picture and wiring diagrams below to solder all the pieces. Your finish product may not look like mine and that is okay. Wire it in the most convenient method. I measured each wire cut and stripped the ends and then soldered them...

Solder on the Headers
Instructions from Autonomous Agri-robot Control System
The headers for the Nanos, compass, Ublox, Emic TFT and SIM800 are all standard male - female 0.1" pitch and are relatively easy to solder - so do these first. The main 2 MCUs push onto the underside of the PCB and the headers for the MEGA 2560...

solder&test MK2
Log from PiBoy-Zero
ok, again repopulating the board with the components grouped by function (the raspberry-zero and the powerboost 500 are already mounted)first: soft-powerconnecting the lipo battery and hitting the power button the pi boots, and pulling the gpio down...

Using a Solder Paste Stencil
Log from Vinduino, a wine grower's water saving project
For upcoming trial installations, I need 25 Vinduino printed circuit boards. Not a sufficient enough quantity for cost effective outsourcing of assembly. The new version of the Vinduino board has a good number of SMD components, and after building the...

Solder wires to the controls
Instructions from Turnado Hardware MIDI Controller
Solder wires to the following control pins: Joystick modules:X GND VCCSwitched rotary encoders: Pin A (left pin of 3-set) Pin B (right pin of 3-set) Switch (either pin of the 2-set)GND 1 (centre pin of 3-set)GND 2 (remaining...

Notes on How To Solder Belly Connectors
Log from VDC-II
I have been thinking about how to reliably solder the surface-mount pin headers to the TinyFPGA BX module for some time now. I think I've come across a solution.Solder on the 14-pin outer/through-hole connectors. It’s important that they be soldered...

Solder speaker and power right angle pin headers
Instructions from Stylish!
They all take 2 x 1 pin angled pinheaders. The battery connectors point away from the speaker. The speaker connector points straight down.

Solder X wires between FPC breakout board to the Microcontroller.
Instructions from QMK Powered Laptop Keyboard
For me X = 24. and i had poor experience with digital pin 33 and digital pin 25. this is attributed to set up issues which i am not sure how to solve so i just switched pins.i used wire wrapping wire for this, as i wanted to maintain flexibility and...

Solder WS2812B RGB LEDS, or 4 x 1 female pinheader for external LED ring
Instructions from Stylish!
If you are not using an external LED ring, you'll have to solder the surface mount WS2812B RGB LEDs by hand. I think it works best if you use lots of flux, get the part into place, and then hit it with solder. Be aware of the corner with the notch...

Step 22: Solder the Micro JST female connectors to the sub-sea cable
Instructions from "Mercator Origins": Sat Nav & Telemetry for Divers
Prepare the float box end of the sub-sea cable by soldering 2 x 2-way Micro JST female connectors to the 4-core cable. Ensure the wire colours correspond to the connections made in Step 5. Plug 1 corresponds to Socket 1 and Plug 2 corresponds to Socket...

if you need to replace sensor, solder a new one on from digikey
Log from mlx90640 sensor works w 800 bytes
i had damaged a sensor 110 deg x 75 deg, which is about 80$ and shipping. i did this when experimenting with the highest frequencies. chip spec is 1mhz. i ran above this testing it. for reading ram it seemed ok. it corrupted data somewhere...

How to solder a 1 mm x 1.5 mm, 6 pad USON package IC
Hacker page by Frank Buss
This page describes how I tested a TPS3420 reset chip on a breadboard. First I glued the chip in dead bug style on a SMD adapter board: Then I tinned the pads of the IC and of the SMD adapter (the pink things at the left side are my fingers) : For connecting...

Cumulus Wireless Sensor Platform
Instructions from Cumulus Wireless Sensor Platform
Solder the 2 x 22pF Supporting Capacitors for the Crystal Oscillator

|<
<
3
4
5
6
7
>
>|