1979 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

Soldering knowledge
Instructions from Chopper Nixie Clock
You need to solder everything to pcb board

Brightenmacher
Instructions from Brightenmacher
Slide the driver PCB and battery holder into the main body and screw everything together.

Soldering and Wiring
Instructions from TeleBall - Retro Handheld Game Console
Solder and wire everything. The case and PCB design guarantee, that no additional screws or fittings are needed: Everything fits together thanks to the custom 3D printed case and soldering the 8x8 LED display on the PCB will hold the PCB and the case...

Attach the button and Wire Everything Up
Instructions from HAL 9000
I used a breadboard to start with, but ultimately made up a PCB. Eagle files are with everything else.

Fit everything into the Housing
Instructions from LoRaLamp AIRQuality
No is the time to fit everything into the Head of the lamp. To fit everything in this Tight space you must DREMEL some pieces out of the Metal head. With a DREMEL this is done in around 5 min. Your Lamp Head must look like this before installing the...

TI-84+ SE Backlight
Instructions from TI-84+ SE Backlight
Assemble your LCD sandwich with the EL panel on the back, then the polarizer, then the glass. You can use some scotch tape around the edge to hold everything in place. I used some putty to stick the whole thing to the PCB, but you could also use some...

Halloween Blinky Eye Lights
Instructions from Halloween Blinky Eye Lights
I bent the LED strip in half as close to the PCB as possible, and taped that to the outside of the roll. I then taped circular pieces of cardboard to the ends to block light and taped everything together with significant amounts of [inexpensive] masking...

Mobile temperature controlled soldering iron
Instructions from Mobile temperature controlled soldering iron
The off the shelve HAKKO controller from Ebay comes shrink wrapped with display and buttons integrated on the PCB. To make it more useable and have everything integrated into a nice case, I first desoldered the display such that I can put it on the front...

Assemble the board, battery and case together
Instructions from ESP32 Powered Smart Plant Monitor
If you opted to build a complete project like i did, now is the time to asseble everything together.The case has specific slots for the battery, display and the PCB to fit in so keep that in mind in case you decided to use different components

Single Chip AVR BASIC Computer
Instructions from Single Chip AVR BASIC Computer
Completed PCB: Once I had all the components and had received the PCB, I assembled it and carried out some basic multimeter tests ensuring no short circuits were present (mainly ensuring no pins had shorts to the ground plane). No issues were present...

Assemble everything
Instructions from Lor's Electronic Heart
1. Cover the cell with Thread to make it bit not ugly.2. Place all the components on perf board before soldering to make sure everything fits under the board size.3. Solder NE555 ic with other passive components including the tactile switch, then solder...

Crazy Clock
Instructions from Crazy Clock
Carefully take stock of the interior of the movement. Some movements have most of the gears sitting on a tray that you can lift out away from the PCB and coil. The Quartex movement has everything encased in a plastic sub-chassis that can be removed as...

Waffle: a pocket-sized digital radio system
Instructions from Waffle: a pocket-sized digital radio system
Complete assemblyInsert the D-pad in the main body, check the fit: it should be pretty lose and allow the pad to move up and down easily. Slide the main PCB in the case. Finish by connecting the radio module and snapping the lid on the case. Everything...

Check you have everything
Instructions from Tindie Blinky LED Badge
Included in the kit Tindie Badge PCBSwitch (not shown in photos)2 LEDsBatteryBattery holderPinPin backing You will also need Soldering IronTweezersSafety glassesWire cuttersSolderFlux

Checking Voltage
Instructions from Ariadne Headband
After everything is connected switch the button and power it, then check the voltage output from step-up converter module and by turning its potentiometer adjust output voltage to about 6,5V. Next press in right oriented arduino Nano and measure voltage...

1
2
3
4
5
>
>|