13548 Results for "《〈 문의 OIO↗5793↗7458 》〉강남초원의집㉩⅓everythingァ강남유흥강남룸㏁evidently 강남초원의집강남더킹 강남더킹‡강남룸Ⅹfaintly㈆"

take it apart and inspect it
Instructions from Dial-a-Memory
This is the interesting part. Two phones which have the same function, and look almost exactly the same on the outside can be engineered completely differently inside. Some have discrete components visible, some have everything hidden in...

Assemble
Instructions from WEI ahead
For the third step, assemble everything, the arduino card and the flexy-hand and try to make everything work. Here are pictures of all the cable placement between the arduino card, the servo motor and the potentiometre ( the muscle sensor broke). we...

Cables
Instructions from Pentesting BBU Dropbox
Here are the loose cables I made for plugging in power and network. You don't necessarily have to have plugs and jacks on everything. I chose to make things easily removed, rather than solder everything directly. (This step can be done later.) Cut one...

Assemble everything
Instructions from Lor's Electronic Heart
1. Cover the cell with Thread to make it bit not ugly.2. Place all the components on perf board before soldering to make sure everything fits under the board size.3. Solder NE555 ic with other passive components including the tactile switch, then solder...

Test....
Instructions from Black & Decker - Dust Buster: battery replacement
Put the battery pack back together with the motor.Careful, the motor might be switched on!Switch on the dust buster and check if it is proper running. Check if all the cells are connected well!If everything is fine, check if the charging is working.Double...

Re-assemble and Test
Instructions from Internal Battery Mod for Korg NTS-1 Synth
Now you can put the NTS-1 board back in place to test if everything works. The red wire than goes inside should be placed in the empty space on the top-left side of the board, as pictured here. Before going any further, it's time to test if everything...

Installation
Instructions from MQTT2LoRa Bridge
After all external dependencies are installed we can build the main bridge. For this we clone this repo to an arbitrary location, e.g. to /home/pi/projects as in our case. Execute the following command if no projects directory exists...

Miter-box cuts (mostly 90 degrees but precise)
Instructions from The Learner's Heliostat
Frame the UJ as shown except that the chamfer is on the wrong end. Complete the cuts and keep an eye on the humidity. I gather that for best results, you condition all lumber in the room where it will be cut (done) and cut everything the same day. (Or...

Avengers ! Assemble !
Instructions from Wall-U
Assemble everything! the chassis with the secondary wheels are placed under the body (make sure the tracks are parallel to each other). The main wheels are attached to the motors through the small circular holes on the sides. The arms' mechanisms...

Program the chip
Instructions from OpenProg All-In-One
After you've soldered everything, download the HEX file from the firmware repository and program it onto the PIC. The marked "MPLAB_SNAP" connector matches the pinout of the Snap - if you're using a PICKit then you will need to utilise jumper...

Trombino
Instructions from Trombino
Drill two holes in the lower half of theArduino box and fix it to the top of the potentiometer housing. Thread wires through the holes. Add in the Arduino, ethernet shield and breadboard and hook up the parts currently attached to the housing. Open up...

Turn a cigarette lighter into an IR Nikon remote
Instructions from Turn a cigarette lighter into an IR Nikon remote
6.Mount everything back into the cigarette lighter and put your Nikon camera into remote controlled mode. Each time you try to turn on the LED lighter, the lighter will send an IR set of pulses. Your camera will receive these infrared pulses and take...

Briefcase PC
Instructions from Briefcase PC
The keyboard receiver was initially under the acrylic but didn't always see the keyboard so I moved it up and just behind the LCD. You can see it sticking out on the right side and works well. My friend used a USB laptop sized keyboard and was able to...

Crazy Clock
Instructions from Crazy Clock
Carefully take stock of the interior of the movement. Some movements have most of the gears sitting on a tray that you can lift out away from the PCB and coil. The Quartex movement has everything encased in a plastic sub-chassis that can be removed as...

PiP: Raspberry Pi Portable Slate Computer
Instructions from PiP: Raspberry Pi Portable Slate Computer
Next is to solder the 3.5mm headphone jack to the Pi so it can be extended to the casing of the portable. Also solder your portable battery pack to the micro usb input for power on the RPi.(Running some tests and checking to make sure everything works...

|<
<
4
5
6
7
8
>
>|