Close
0%
0%

Jacob

Mechanical Engineer, Free Software Dev, snowflake

Nordland, Norway
Following
Send a private message
Similar accounts worth following
2 Followers
29 Following
6 Projects
33 Likes
jacob
Send a private message

This user joined on 05/05/2021.

Proud member of

Makerspace Bodø
1.1k
11
3
16
A handle which helps folks with shaky hands to drink from a variety of cups
Project Owner Contributor

Mechanical Anti-tremor cup handle

jacobJacob

1.3k
15
6
14
Small surface vessel
Project Owner Contributor

small surface vessel

jacobJacob

297
2
0
2
FOSOPAS for short
Project Owner Contributor

Farmers'Open Source Optical Predator Alert System

jacobJacob

1
0
1
The spice to reach for in a pinch
Project Owner Contributor

Anti-Salt

jacobJacob

0
0
0
Because drinking cups of different sizes shouldn't need different lids
Project Owner Contributor

Universal cup lid

jacobJacob

52
0
0
0
Dragging a suitcase or trolley bag over even short stretches of snow can be a literal drag. Let's fix that.
Project Owner Contributor

Snow-glider for suitcase and bag

jacobJacob

0
2
A membership makerspace in the midnight sun
Project Owner Contributor

Makerspace Bodø

jacobJacob

74.5k
2.3k
13
553
An Odrive + steppers based construction, with 5x 3D printed hollow shaft reducers and an internal CAN network.
Project Owner Contributor

Atlas - 6DOF 3D printed universal robot

damian-lickindorfDamian Lickindorf

67.4k
419
76
334
A small Portable Wind Turbine, mostly 3D printed!
Project Owner Contributor

3D PRINTED PORTABLE WIND TURBINE

adriancubasadriancubas

12.9k
2.8k
17
49
LP3D is an (almost) fully lasercut, low component count 3D printer with all linear motion components cut directly into the frame.
Project Owner Contributor

LP3D: A fully lasercut kit 3D printer

luke-wallaceLuke Wallace

12.9k
93
1
76
The ideal machine for recycling plastic bottles into 3D printer filament. Team Members: Reiten (Yang) Cheng, Swaleh Owais
Project Owner Contributor

Polyformer - Ideal Filament Recycler

swaleh-owaisSwaleh Owais

11.5k
1.7k
1
3
Run Stremio on Raspberry Pi with a kiosk look
Project Owner Contributor

Install Stremio on Raspberry Pi

shivasiddharthshivasiddharth

6.7k
88
0
75
An open-source, low-cost, large-format 3D printer that can print directly from shredded plastic trash instead of filament
Project Owner Contributor

The Trash Printer - Version 3

sam-smithSam Smith

4.8k
4.6k
1
15
This projects converts a Bobby-Car (children's ride-on toy) to electric by using 4 Hoverboard motors, VESC controllers and an ESP32
Project Owner Contributor

Electric Bobby-Car

peter-ptziPeter Pötzi

4.2k
3.8k
8
15
Stream Deck, but utilizing various Raspberry Pi's!
Project Owner Contributor

DIY Stream Deck With Raspberry Pi (PiDeck)

turkeydevTurkeyDev

3.2k
2.6k
2
19
Teach elementary and middle-school students about robotics with a DIY battle bots kit.
Project Owner Contributor

Educational Battle Bots

misty-lackieMisty Lackie

2.6k
2.6k
0
12
How to generate frequencies below 10Hz using a PC, an amplifier, and a handful of components.
Project Owner Contributor

Extreme Low Frequency Signal Generator

joseph-eoffJoseph Eoff

2.2k
1.9k
1
17
A MicroPython gaming system featuring a Wemos D1 mini, OLED display, joystick, buttons, fancy LEDs and a buzzer.
Project Owner Contributor

GamerGorl

brian-wagnerBrian Wagner

2.2k
50
1
37
Another mostly 3D printed windturbine
Project Owner Contributor

WinDIY_2 - Horizontal Axis Wind Turbine

fabFab

1.9k
27
5
24
A mostly 3D printed pelton turbine
Project Owner Contributor

Printon Turbine - 3D printed pelton turbine

fabFab

1.4k
1.4k
0
44
This workshop is focused on reverse engineering and utilizing hardware-level debuggers.
Project Owner Contributor

Remoticon: The Hackers Guide to Hardware Debugging

lutetiumLutetium

789
789
0
4
Developing a cheap DIY alternative to expensive machined ballscrew actuators (with a little less precision). For humanoid robots.
Project Owner Contributor

3D Printed Ballscrew Linear Actuator

anthroboticsAnthrobotics

565
565
0
1
Self-Programmed Software with Deep Learning
Project Owner Contributor

Gemini Project

nick-bildNick Bild

474
474
1
4
smallest raspberry pi today 2020
Project Owner Contributor

tiny pi

kamahalanmarkkamahalanmark

319
20
0
20
Accessibilità aims to do what Arduino did for Microcontrollers for accessibility electronics and interfaces for Wheel chairs and similar
Project Owner Contributor

Accessibilità

avrAVR

View all

Share this profile

Share

Bits

Send a private message to Jacob

Become cool instantly

Create your Hackaday.io profile like Jacob and many others

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2023 Hackaday

Report user as inappropriate

You are about to report the user "Jacob", please tell us the reason.