0%

0%

Gregor

Industrial designer

Den Haag

Following Follow me

Send a private message

Similar accounts worth following

Send a private message

This user joined on 07/08/2014.

My Projects

The 2018 Hackaday Prize

A coin-cell powered ATTiny board with popular peripherals (USB, potmeter, slide/tact switch, piezo buzzer, LED) to jump-start tiny projects.

Duinothrowie

Supplyframe DesignLab: 2022 Hackada…

Refurbishing a behemoth of an industrial 3D-printer to working condition after it has been left for dead in the shed of a big company

Stratasys Dimension SST Extruder sensor repair

The Bus-powered RS485 Shield is an Arduino-compatible shield that allows full-duplex communication over long distances between 2+ Arduino's.

Arduino Bus-powered RS485 Shield

Connect any shield to an Arduino with a flexible flat cable up to 50cm in length. Use an LCD screen with a button shield without blocking!

Arduino Flat Flexible Connector (FFC) Shield

Projects I Like & Follow

The 2018 Hackaday Prize

Affordable and open-source LiDAR based on 3x VL53L0X ranging sensor

xLiDAR

The 2018 Hackaday Prize

AMS's new AS7265X 3-chip set promises a compact, 18-channel, 20 nm FWMH spectrometer for less than $25

Compact, $25 spectrometer

kris-winer Kris Winer

Yet another Raspberry Pi Computer (non-official carrier board for CM4).

MirkoPC -> CM4 carrier board

Hackaday Prize 2019

Small and powerfull controlling unit powerd from USB-C-PD

USB-C-PD Soldering Pen for Weller RT Tips

thomas-leputsch Thomas Leputsch

The 2018 Hackaday Prize

... is designed for direct drive wheels for swarm robots

PCB stepper motor

Supplyframe DesignLab: 2023 Hackada…

Extremely affordable pocket-friendly, designed to provide a wide range of hardware testing and debugging functions in a compact and low-cost

Felini - Revolutionary Pocket-Sized Electronic Lab

chu-tien-thinh-obitvn Chu Tien Thinh (obitvn)

Ultra low-cost controller for brushless servo based on the B-G431B-ESC1 Discovery kit by ST

B-G431B-ESC Brushless Servo Controller

pat92fr pat92fr

A 3D printer for printing with welding wire

Wire 3D Printer

dominik-meffert Dominik Meffert

Supplyframe DesignLab: 2022 Hackada…

The ideal machine for recycling plastic bottles into 3D printer filament. Team Members: Reiten Cheng (Project Founder), Swaleh Owais

Polyformer - Ideal Filament Recycler

swaleh-owais Swaleh Owais

Kinetic sculptures based on Nautilus gears

Nautilus Sculptures

vipin-m Vipin M

Amazon Echo Show 10 3rd gen Teardown

txyzinfo txyz.info

Hackaday Prize 2020

Test any electronic component with this pocket component tester

Component Tester in a Keychain

akshay-baweja Akshay Baweja

Two hearts are better than one, so why not have five. Quadcore RPI CM4 and a MCU on a single board for true all-in-one 3D printer control.

Sigmoid S7P 3D Printer Control Board

Supplyframe DesignLab: 2023 Hackada…

Differential scope probe

PD150

3D printed toroidally wound axial flux permanent magnet air core motor. 3DTAFPM?

3D Printed Axial Flux Motor

colby-johnson Colby Johnson

This is a project where I built a sputtering magnetron to deposit thin conductive films on surfaces.

Sputtering Magnetron

steve-hernandez Steve Hernandez

Supplyframe DesignLab: 2023 Hackada…

The Ultra-Compact Powerhouse for LoRa Debugging and Connectivity

LoShark

reimu-notmoe Reimu NotMoe

Using your phone’s camera and IMU to position stabilize a self balance robot – no additional sensors needed

World’s first camera stabilized self balance robot

View all

Bits

Kris Winer wrote 06/13/2018 at 15:29

Thanks for following my $25 Spectrometer project!

Are you sure? yes | no