Close

Your browser (Internet Explorer) is out of date.

Update your browser for more security, comfort and the best experience on this site.

Update Internet Explorer

Projects Julien likes and follows

1.4k
1.2k
16
Create 3D printing filament from PET flakes. Bottle → Flakes → FILAMENT → 3D Printing
Project Owner Contributor

3D printer filament maker

PETMAT z.ú.PETMAT z.ú.

7k
909
44
LP3D is an (almost) fully lasercut, low component count 3D printer with all linear motion components cut directly into the frame.
Project Owner Contributor

LP3D: A fully lasercut kit 3D printer

Luke WallaceLuke Wallace

991
847
7
https://github.com/mhe747/dawnboard/wiki
Project Owner Contributor

BeagleSDR

Mich MichMich Mich

19.1k
435
156
Itsy-chipsy is a chip platform that enables a multi-block service like-oshpark capable to offer area for your own chip, for as low as $100.
Project Owner Contributor

Itsy-Chipsy: Make your own $100 chip

OnchipOnchip

46.6k
417
286
AMS's new AS7265X 3-chip set promises a compact, 18-channel, 20 nm FWMH spectrometer for less than $25
Project Owner Contributor

Compact, $25 spectrometer

Kris WinerKris Winer

29.7k
372
266
An open hardware reading device
Project Owner Contributor

The Open Book Feather

joey castillojoey castillo

25.1k
361
280
An efficient and compact generator that can be coupled with wind turbines or water wheels to produce upwards of 100W
Project Owner Contributor

Portal Point Generator

VijayVijay

26.9k
268
250
A 252 electromagnet-matrix that controls Ferrofluid
Project Owner Contributor

Fetch: A Ferrofluid Display

Applied ProcrastinationApplied Procrastination

27.8k
261
206
A mostly printed digital microscope powered by a Rasperry Pi Zero W
Project Owner Contributor

Pi Microscope

BraunsCNCBraunsCNC

18.7k
154
119
Building all the tools neccesary to make chips at home.
Project Owner Contributor

Semiconductors @ Home

NixieNixie

9.5k
151
300
University digital Logic Learning Xtensible board release 3 with SDRAM
Project Owner Contributor

ULX3S powerful ECP5 board for open source FPGA

radiona.orgradiona.org

11.7k
100
108
Mini vertical wind generator, with nylon blades and supports printed with 3D printer and based on electric motor with a power of 55 watts.
Project Owner Contributor

Mini Vertical Wind Generator 3D printed

Vittorio LoschiavoVittorio Loschiavo

8.4k
69
63
An all-in-one, made to hack step sequencer built around the Teensy platform with LiPo charging, touch TFT, encoders, buttons, and RGB leds.
Project Owner Contributor

Teensy Beats Shield

Chris MillerChris Miller

23.7k
53
36
Messing around with Annax Flip-Dot displays.
Project Owner Contributor

Flip-Dot Display & DIY Controller

Frederic LFrederic L

5.5k
52
55
I always wanted a large, affordable E-Ink screen to play around with. The result is a board to talk to E-Paper screens with an ESP32.
Project Owner Contributor

EPDiy: 9.7"/6" E-Paper controller

ValentinValentin

4.8k
47
31
Modular power generation system for powering and charging small electronic devices
Project Owner Contributor

Power Generation Modules

Cole BCole B

4.6k
45
44
USB Type C has up to 100W of charging capability, perfect for a multicell charger
Project Owner Contributor

Small Multicell USB Type C Charger

Chris HamiltonChris Hamilton

3.8k
41
42
Fast, small, available. Pick any three.
Project Owner Contributor

CP/M 50 Mk II

jessexmjessexm

1.1k
24
18
Writing my own Gcode generator for pen plotter
Project Owner Contributor

Gcode Playground

Mike SzczysMike Szczys

189
3
4
https://github.com/mhe747/sumpx15/wiki
Project Owner Contributor

BeagleSDR Sump

Mich MichMich Mich

197
2
2
Simple dummy load using wire wound resistors.
Project Owner Contributor

Resistive Load Tester DIY

Robert SälgRobert Sälg

Going up?

About Us Contact Hackaday.io Give Feedback Terms of Use Privacy Policy Hackaday API

© 2020 Hackaday